10 rear suspension, HYUNDAI PONY
[ Pobierz całość w formacie PDF ]
REAR
SUSPENSION
Return To Main Table of Contents
2
7
REAR AXLE HUB
.....................................
13
GENERAL
GENERAL
SPECIFICATIONS
Suspension system
Trailing arm with coil spring
Coil spring
Wire dia. x O.D. x free height
10.7 x 117.7 x 306.3
(0.42 x 4.63 x 12)
Green
mm (in.)
Identification color
Shock absorber
Type
Max. length
Min. length
Stroke
Identification color
Hydraulic, cylindrical, double acting type
411 mm (16.18 in.)
266 mm (10.47 in.)
145 mm (5.71 in.)
Red
SERVICE STANDARD
Toe
Camber
NOTE
The rear wheel alignment is set at the factory and cannot be adjusted. If toe or camber is not within the
specification, replace the damaged parts.
TIGHTENING TORQUE
Nm
kg.cm
Ib.ft
65-80
88-108
900-1100
Rear suspension arm assembly fixture mounting nuts
Both ends of suspension arm nuts
Rear shock absorber mounting nuts (both)
Rear spindle to backing plate bolts
Hub nut
88-108
900-1100
65-79
64-78
650-800
47-58
49-59
500-600
36-43
147-196
1500-2000
108-145
55-2
GENERAL
LUBRICANTS
Quantity
Recommended lubricants
As required
Inside of suspension arm (L.H.) and outer
periphery of suspension arm (R.H.)
Bushing A and B
Multipurpose grease
SAE J310, NLGI No.3
Multipurpose grease
SAE J310, NLGI No.3
Multipurpose grease
SAE J310, NLGI No.3
Multipurpose grease
SAE J310, NLGI No.2
Multipurpose grease
SAE J310, NLGI No.2
As required
As required
Inside of dust cover and lip
As required
Wheel bearings, oil seal lip and inside
50-60 gm
(1.8-2.1 oz)
Inside hub cap
55-3
GENERAL
SPECIAL TOOLS
Tool
(Number and name)
Use
Illustration
Installation of rear hub outside bearing
outer race. (use with 09500-21000)
09432-21700
Bearing outer race installer
Removal & installation of oil seal and
bearing.
09500-21000
Bar
Removal of rear wheel bearing outer
09517-21400
Drift
Installation of rear suspension arm
bushing. (use with 09555-21100)
09555-21000
Bar
Installation of rear suspension arm
bushing A and B. (use with 09555-
21000)
09555-21100
Bushing installer
55-4
GENERAL
TROUBLESHOOTING
Remedy
Probable cause
Symptom
Tighten to specified torque
Suspension securing bolt(s) loose
Loose wheel nuts
Abnormal sound
Replace damaged parts
Faulty shock absorber
Worn bushings
Damaged or worn wheel bearings
Components bent or distorted
Broken coil spring
Balance
Wheel or tire unbalanced
Inflate to specification
Improper tire inflation
Replace
Defective tire
Inflate to specification
Improper tire inflation
Poor ride control
Replace
Defective tire
Tighten to specification
Loose wheel nuts
Suspension securing bolt(s) loose
Damaged or broken components
Worn bushings
Faulty shock absorber
Sagging or broken coil spring
Replace
Improper rear wheel alignment
Replace parts
Improper rear wheel alignment
Replace parts
Abnormal tire wear
Replace parts
Bent or damaged parts
Inflation specification
Improper inflation
Balance
Wheel or tire imbalance
Adjust or replace
Loose wheel bearings
Inspect and repair
Faulty shock absorber
55-5
[ Pobierz całość w formacie PDF ]